APRS Track Direct

My position About ☰

reset

CT4TX-8 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object CT4TX-8. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1786740598	58 Pkt	-54 dBm	0.08 V
1786739988	638 Pkt	-57 dBm	0.08 V
1786738511	611 Pkt	-58 dBm	0.06 V
1786737042	700 Pkt	-58 dBm	0.08 V
1786735508	741 Pkt	-58 dBm	0.08 V
1786733329	47 Pkt	-60 dBm	0.06 V
1786731665	773 Pkt	-58 dBm	0.08 V
1786730069	740 Pkt	-58 dBm	0.08 V
1786728504	694 Pkt	-58 dBm	0.08 V
1786726982	697 Pkt	-57 dBm	0.06 V
1786725457	682 Pkt	-58 dBm	0.08 V
1786723953	591 Pkt	-53 dBm	0.08 V
1786722113	63 Pkt	-57 dBm	0.06 V
1786721290	666 Pkt	-56 dBm	0.06 V
1786717223	58 Pkt	-59 dBm	0.08 V
1786716267	647 Pkt	-57 dBm	0.06 V
1786714764	689 Pkt	-49 dBm	0.06 V
1786713255	759 Pkt	-61 dBm	0.06 V
1786710783	43 Pkt	-56 dBm	0.06 V
1786710276	704 Pkt	-58 dBm	0.08 V
1786706977	44 Pkt	-57 dBm	0.08 V
1786706403	775 Pkt	-57 dBm	0.06 V
1786704825	748 Pkt	-57 dBm	0.08 V
1786701742	52 Pkt	-48 dBm	0.08 V
1786701468	691 Pkt	-55 dBm	0.06 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)