APRS Track Direct

My position About ☰

reset

YO3FVR-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO3FVR-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Tin*
1732292099	12.23 Volt	77 Pcnt	6 C
1732291801	12.23 Volt	80 Pcnt	6 C
1732291499	12.23 Volt	85 Pcnt	6 C
1732290901	12.15 Volt	87 Pcnt	6 C
1732290899	12.15 Volt	87 Pcnt	6 C
1732290300	12.23 Volt	88 Pcnt	6 C
1732290001	12.23 Volt	100 Pcnt	6 C
1732289700	12.23 Volt	95 Pcnt	6 C
1732289101	12.23 Volt	84 Pcnt	6 C
1732289099	12.23 Volt	84 Pcnt	6 C
1732288499	12.23 Volt	83 Pcnt	6 C
1732288201	12.3 Volt	77 Pcnt	6 C
1732287900	12.3 Volt	79 Pcnt	6 C
1732287301	12.23 Volt	79 Pcnt	6 C
1732287300	12.23 Volt	79 Pcnt	6 C
1732286700	12.3 Volt	78 Pcnt	6 C
1732286100	12.38 Volt	81 Pcnt	6 C
1732285501	12.3 Volt	89 Pcnt	6 C
1732285500	12.3 Volt	89 Pcnt	6 C
1732284900	12.38 Volt	88 Pcnt	6 C
1732284601	12.38 Volt	93 Pcnt	6 C
1732284300	12.38 Volt	93 Pcnt	6 C
1732283700	12.38 Volt	91 Pcnt	6 C
1732283100	12.45 Volt	92 Pcnt	6 C
1732282500	12.45 Volt	92 Pcnt	6 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Vsol: 0, 0.075, 0

Isol: 0, 0.1, 0

Eff1h: 0, 1, 0

Tin: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)