APRS Track Direct

My position About ☰

reset

SR6WXP Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR6WXP. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Tempre*
1744818111	11 Pkt	2 Pkt	42 DegC
1744817511	10 Pkt	4 Pkt	42 DegC
1744816909	12 Pkt	2 Pkt	42 DegC
1744816310	16 Pkt	3 Pkt	42 DegC
1744815708	8 Pkt	4 Pkt	42 DegC
1744815108	14 Pkt	7 Pkt	41.5 DegC
1744814504	7 Pkt	4 Pkt	41.5 DegC
1744813903	12 Pkt	3 Pkt	41.5 DegC
1744813301	12 Pkt	3 Pkt	41 DegC
1744812701	17 Pkt	6 Pkt	41 DegC
1744812092	8 Pkt	4 Pkt	41 DegC
1744811490	10 Pkt	4 Pkt	40.5 DegC
1744810285	12 Pkt	3 Pkt	40.5 DegC
1744809683	10 Pkt	2 Pkt	40 DegC
1744809083	14 Pkt	4 Pkt	40 DegC
1744808480	9 Pkt	2 Pkt	40 DegC
1744807880	14 Pkt	3 Pkt	40 DegC
1744807277	8 Pkt	2 Pkt	39.5 DegC
1744806678	12 Pkt	7 Pkt	39.5 DegC
1744806073	8 Pkt	4 Pkt	39.5 DegC
1744805473	11 Pkt	6 Pkt	39.5 DegC
1744804872	6 Pkt	3 Pkt	39 DegC
1744804272	11 Pkt	3 Pkt	39 DegC
1744803670	7 Pkt	5 Pkt	39 DegC
1744803063	10 Pkt	6 Pkt	39 DegC

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

HostTx10m: 0, 1, 0

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)