APRS Track Direct

My position About ☰

reset

METHOD Telemetry

This is the latest recevied telemetry packets stored in our database for station/object METHOD. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1732295035	13.83 Volt	500 Pkt	150 Pkt	87 Pcnt
1732294434	13.83 Volt	500 Pkt	150 Pkt	87 Pcnt
1732293833	13.83 Volt	520 Pkt	150 Pkt	87 Pcnt
1732293233	13.83 Volt	520 Pkt	150 Pkt	88 Pcnt
1732292632	13.67 Volt	500 Pkt	150 Pkt	88 Pcnt
1732292032	13.83 Volt	450 Pkt	140 Pkt	87 Pcnt
1732291431	13.83 Volt	430 Pkt	130 Pkt	86 Pcnt
1732290831	13.83 Volt	410 Pkt	110 Pkt	87 Pcnt
1732290230	13.83 Volt	400 Pkt	110 Pkt	86 Pcnt
1732289629	13.83 Volt	380 Pkt	100 Pkt	84 Pcnt
1732289029	13.83 Volt	380 Pkt	100 Pkt	85 Pcnt
1732288428	13.83 Volt	380 Pkt	100 Pkt	84 Pcnt
1732287828	13.83 Volt	370 Pkt	100 Pkt	83 Pcnt
1732287227	13.83 Volt	350 Pkt	110 Pkt	81 Pcnt
1732286627	13.83 Volt	340 Pkt	110 Pkt	81 Pcnt
1732286026	13.83 Volt	350 Pkt	110 Pkt	80 Pcnt
1732285425	13.83 Volt	350 Pkt	110 Pkt	79 Pcnt
1732284825	13.83 Volt	380 Pkt	110 Pkt	79 Pcnt
1732284224	13.67 Volt	390 Pkt	120 Pkt	80 Pcnt
1732283624	13.83 Volt	410 Pkt	120 Pkt	80 Pcnt
1732283023	13.83 Volt	410 Pkt	120 Pkt	81 Pcnt
1732282422	13.83 Volt	400 Pkt	120 Pkt	81 Pcnt
1732281822	13.83 Volt	400 Pkt	130 Pkt	82 Pcnt
1732281221	13.83 Volt	380 Pkt	120 Pkt	82 Pcnt
1732280621	13.83 Volt	370 Pkt	120 Pkt	83 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)