APRS Track Direct

My position About ☰

reset

VE7EOL-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VE7EOL-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Battery*	Temp*
1753989563	13.45 Volts	51.06 Deg.C
1753989558	13.21 Volts	51.06 Deg.C
1753989525	13.62 Volts	50.08 Deg.C
1753989491	13.24 Volts	50.08 Deg.C
1753989440	13.51 Volts	49.1 Deg.C
1753989375	13.33 Volts	47.15 Deg.C
1753989368	13.45 Volts	47.15 Deg.C
1753989346	13.6 Volts	46.66 Deg.C
1753989326	13.92 Volts	46.17 Deg.C
1753989254	13.54 Volts	43.72 Deg.C
1753989224	13.65 Volts	42.74 Deg.C
1753989208	13.83 Volts	42.26 Deg.C
1753989199	13.39 Volts	42.26 Deg.C
1753989194	13.45 Volts	42.26 Deg.C
1753989183	13.54 Volts	41.77 Deg.C
1753989173	13.48 Volts	41.77 Deg.C
1753989169	13.68 Volts	41.77 Deg.C
1753988994	13.57 Volts	39.32 Deg.C
1753981847	13.98 Volts	33.94 Deg.C
1753981842	13.8 Volts	32.96 Deg.C
1753981830	13.92 Volts	32.48 Deg.C
1753981821	14.01 Volts	32.48 Deg.C
1753981816	13.92 Volts	32.48 Deg.C
1753981812	13.74 Volts	32.48 Deg.C
1753981801	13.48 Volts	31.5 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)