APRS Track Direct

My position About ☰

reset

W1GMM-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W1GMM-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	DigiRpt*	Temp*
1750176287	17 Pkts	17 Pkts	3 Pkts	37 C
1750172687	16 Pkts	16 Pkts	7 Pkts	37 C
1750169087	16 Pkts	16 Pkts	5 Pkts	36 C
1750165487	27 Pkts	27 Pkts	16 Pkts	36 C
1750161887	14 Pkts	14 Pkts	1 Pkts	36 C
1750158287	13 Pkts	13 Pkts	4 Pkts	36 C
1750154687	9 Pkts	9 Pkts	1 Pkts	36 C
1750151088	14 Pkts	14 Pkts	1 Pkts	36 C
1750147488	19 Pkts	19 Pkts	3 Pkts	36 C
1750143888	16 Pkts	16 Pkts	3 Pkts	36 C
1750140287	28 Pkts	27 Pkts	9 Pkts	36 C
1750136687	28 Pkts	28 Pkts	2 Pkts	36 C
1750133087	18 Pkts	18 Pkts	3 Pkts	37 C
1750129487	19 Pkts	19 Pkts	6 Pkts	36 C
1750125887	15 Pkts	15 Pkts	3 Pkts	36 C
1750122287	15 Pkts	15 Pkts	2 Pkts	36 C
1750118687	8 Pkts	8 Pkts	0 Pkts	36 C
1750115087	14 Pkts	14 Pkts	3 Pkts	37 C
1750111487	16 Pkts	16 Pkts	1 Pkts	36 C
1750107887	24 Pkts	24 Pkts	16 Pkts	36 C
1750104287	12 Pkts	12 Pkts	6 Pkts	36 C
1750100687	21 Pkts	21 Pkts	4 Pkts	36 C
1750097087	25 Pkts	25 Pkts	7 Pkts	36 C
1750093487	40 Pkts	40 Pkts	27 Pkts	36 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

InetiGate: 0, 1, 0

Temp: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)