APRS Track Direct

My position About ☰

reset

YC1JEL-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YC1JEL-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1790656916	2 Pkt	-56 dBm	0.02 V
1790656534	0 Pkt	-46 dBm	0.02 V
1790656154	0 Pkt	-46 dBm	0 V
1790655770	2 Pkt	-58 dBm	0.02 V
1790655388	0 Pkt	-58 dBm	0 V
1790655006	1 Pkt	-64 dBm	0.02 V
1790654624	0 Pkt	-61 dBm	0 V
1790654242	2 Pkt	-55 dBm	0 V
1790653860	0 Pkt	-57 dBm	0 V
1790653478	0 Pkt	-50 dBm	0.02 V
1790653096	0 Pkt	-57 dBm	0.02 V
1790652715	0 Pkt	-55 dBm	0.02 V
1790652332	0 Pkt	-59 dBm	0 V
1790651950	0 Pkt	-47 dBm	0.02 V
1790651568	0 Pkt	-55 dBm	0 V
1790651186	0 Pkt	-52 dBm	0.02 V
1790650804	1 Pkt	-62 dBm	0 V
1790650422	0 Pkt	-62 dBm	0 V
1790650040	1 Pkt	-61 dBm	0.02 V
1790649658	2 Pkt	-62 dBm	0.02 V
1790649276	1 Pkt	-62 dBm	0.02 V
1790648894	1 Pkt	-63 dBm	0.02 V
1790648512	0 Pkt	-63 dBm	0.02 V
1790648130	2 Pkt	-61 dBm	0 V
1790647747	0 Pkt	-66 dBm	0.02 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)