APRS Track Direct

My position About ☰

reset

F4BYF-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F4BYF-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1732286546	13.8 Volt	70 Pkt	30 Pkt	90 Pcnt
1732284744	13.8 Volt	80 Pkt	30 Pkt	87 Pcnt
1732282943	13.8 Volt	70 Pkt	30 Pkt	90 Pcnt
1732281141	13.8 Volt	60 Pkt	30 Pkt	93 Pcnt
1732277537	13.8 Volt	60 Pkt	30 Pkt	86 Pcnt
1732275736	13.8 Volt	70 Pkt	50 Pkt	92 Pcnt
1732273934	13.8 Volt	80 Pkt	50 Pkt	90 Pcnt
1732272132	13.8 Volt	80 Pkt	40 Pkt	88 Pcnt
1732268529	13.8 Volt	80 Pkt	30 Pkt	91 Pcnt
1732266727	13.8 Volt	70 Pkt	30 Pkt	96 Pcnt
1732264926	13.8 Volt	80 Pkt	30 Pkt	91 Pcnt
1732263123	13.8 Volt	80 Pkt	30 Pkt	78 Pcnt
1732261322	13.8 Volt	90 Pkt	40 Pkt	73 Pcnt
1732259522	13.8 Volt	90 Pkt	40 Pkt	77 Pcnt
1732257720	13.8 Volt	110 Pkt	40 Pkt	75 Pcnt
1732255918	13.8 Volt	120 Pkt	50 Pkt	71 Pcnt
1732254116	13.8 Volt	110 Pkt	50 Pkt	76 Pcnt
1732252314	13.8 Volt	90 Pkt	40 Pkt	79 Pcnt
1732250512	13.8 Volt	130 Pkt	60 Pkt	70 Pcnt
1732248711	13.8 Volt	140 Pkt	80 Pkt	70 Pcnt
1732246909	13.8 Volt	80 Pkt	40 Pkt	76 Pcnt
1732245107	13.8 Volt	40 Pkt	30 Pkt	74 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)