APRS Track Direct

My position About ☰

reset

E27HUQ-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E27HUQ-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1745130849	0 Pkt	-58 dBm	0.25 V
1745130539	0 Pkt	-59 dBm	0.25 V
1745130229	1 Pkt	-61 dBm	0.1 V
1745129919	0 Pkt	-59 dBm	0.1 V
1745129609	0 Pkt	-60 dBm	0.25 V
1745129299	0 Pkt	-60 dBm	0.27 V
1745128989	0 Pkt	-59 dBm	0.25 V
1745128679	0 Pkt	-59 dBm	0.25 V
1745128369	0 Pkt	-59 dBm	0.25 V
1745128059	0 Pkt	-58 dBm	0.1 V
1745127749	0 Pkt	-59 dBm	0.1 V
1745127439	0 Pkt	-59 dBm	0.25 V
1745127129	0 Pkt	-59 dBm	0.25 V
1745126819	0 Pkt	-58 dBm	0.25 V
1745126509	0 Pkt	-59 dBm	0.25 V
1745126199	0 Pkt	-58 dBm	0.25 V
1745125889	0 Pkt	-59 dBm	0.25 V
1745125579	0 Pkt	-59 dBm	0.1 V
1745125269	0 Pkt	-59 dBm	0.25 V
1745124959	0 Pkt	-58 dBm	0.25 V
1745124649	0 Pkt	-57 dBm	0.25 V
1745124339	0 Pkt	-60 dBm	0.25 V
1745124029	0 Pkt	-59 dBm	0.25 V
1745123719	0 Pkt	-59 dBm	0.25 V
1745123409	0 Pkt	-59 dBm	0.25 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)