APRS Track Direct

My position About ☰

reset

SPRFLD Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SPRFLD. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Rx1h*	Rx10m*	Temp*	Vin*
1744866565	630 Pkt	85 Pkt	64.6 F	13.69 Volt
1744866265	640 Pkt	104 Pkt	65.5 F	13.69 Volt
1744866265	640 Pkt	104 Pkt	65.5 F	13.69 Volt
1744865965	630 Pkt	99 Pkt	64.6 F	13.69 Volt
1744865665	630 Pkt	99 Pkt	65.5 F	13.69 Volt
1744865365	620 Pkt	87 Pkt	65.5 F	13.69 Volt
1744865065	620 Pkt	91 Pkt	66.4 F	13.69 Volt
1744864765	620 Pkt	97 Pkt	66.4 F	13.69 Volt
1744864465	620 Pkt	115 Pkt	68.2 F	13.69 Volt
1744864465	620 Pkt	115 Pkt	68.2 F	13.69 Volt
1744864165	600 Pkt	103 Pkt	69.1 F	13.69 Volt
1744863865	590 Pkt	88 Pkt	68.2 F	13.69 Volt
1744863565	590 Pkt	104 Pkt	68.2 F	13.69 Volt
1744863265	580 Pkt	95 Pkt	68.2 F	13.69 Volt
1744862965	570 Pkt	78 Pkt	68.2 F	13.69 Volt
1744862665	580 Pkt	90 Pkt	68.2 F	13.69 Volt
1744862665	580 Pkt	90 Pkt	68.2 F	13.69 Volt
1744862365	570 Pkt	81 Pkt	68.2 F	13.69 Volt
1744862065	570 Pkt	84 Pkt	69.1 F	13.69 Volt
1744861765	560 Pkt	83 Pkt	68.2 F	13.69 Volt
1744861465	570 Pkt	92 Pkt	68.2 F	13.69 Volt
1744861165	560 Pkt	80 Pkt	69.1 F	13.69 Volt
1744860866	550 Pkt	91 Pkt	68.2 F	13.69 Volt
1744860865	550 Pkt	91 Pkt	68.2 F	13.69 Volt
1744860565	520 Pkt	84 Pkt	68.2 F	13.69 Volt

*Used Equation Coefficients:

Rx1h: 0, 10, 0

Rx10m: 0, 1, 0

Dig1h: 0, 10, 0

Temp: 0, 0.9, -83

Vin: 0, 0.07, 0.53

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)