APRS Track Direct

My position About ☰

reset

E25WMA-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E25WMA-7. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1786739635	0 Pkt	-37 dBm	13.78 V
1786738714	0 Pkt	-37 dBm	13.8 V
1786737791	0 Pkt	-37 dBm	13.8 V
1786737079	0 Pkt	-39 dBm	13.84 V
1786736157	0 Pkt	-37 dBm	13.84 V
1786735235	0 Pkt	-37 dBm	13.84 V
1786734313	0 Pkt	-37 dBm	13.82 V
1786733391	0 Pkt	-37 dBm	13.82 V
1786732469	0 Pkt	-36 dBm	13.82 V
1786731547	0 Pkt	-38 dBm	13.82 V
1786730625	1 Pkt	-37 dBm	13.66 V
1786729703	0 Pkt	-38 dBm	13.82 V
1786728781	0 Pkt	-37 dBm	13.82 V
1786727858	0 Pkt	-40 dBm	13.8 V
1786726936	1 Pkt	-40 dBm	13.8 V
1786726014	0 Pkt	-40 dBm	13.8 V
1786725092	0 Pkt	-41 dBm	13.8 V
1786724170	0 Pkt	-40 dBm	13.8 V
1786723248	2 Pkt	-41 dBm	13.7 V
1786722326	0 Pkt	-41 dBm	13.78 V
1786721404	0 Pkt	-40 dBm	13.62 V
1786720482	0 Pkt	-41 dBm	13.74 V
1786719560	0 Pkt	-41 dBm	13.66 V
1786718638	0 Pkt	-40 dBm	13.64 V
1786717716	0 Pkt	-40 dBm	13.64 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)