APRS Track Direct

My position About ☰

reset

SV2AHT-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SV2AHT-12. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	V_Batt*	Value2*	Value3*	Value4*	Value5*
1782506042	2.74 VDC	0	0	0	0
1782506030	2.72 VDC	0	0	0	0
1782506006	2.72 VDC	0	0	0	0
1782505983	2.74 VDC	0	0	0	0
1782505948	2.76 VDC	0	0	0	0
1782505936	2.75 VDC	0	0	0	0
1782505913	2.76 VDC	0	0	0	0
1782505902	2.74 VDC	0	0	0	0
1782505890	2.76 VDC	0	0	0	0
1782505867	2.77 VDC	0	0	0	0
1782505855	2.77 VDC	0	0	0	0
1782505843	2.75 VDC	0	0	0	0
1782505831	2.77 VDC	0	0	0	0
1782505820	2.76 VDC	0	0	0	0
1782505808	2.76 VDC	0	0	0	0
1782505785	2.77 VDC	0	0	0	0
1782505773	2.77 VDC	0	0	0	0
1782505761	2.77 VDC	0	0	0	0
1782505750	2.77 VDC	0	0	0	0
1782505738	2.77 VDC	0	0	0	0
1782505726	2.8 VDC	0	0	0	0
1782505715	2.77 VDC	0	0	0	0
1782505703	2.78 VDC	0	0	0	0
1782505691	2.78 VDC	0	0	0	0
1782505679	2.81 VDC	0	0	0	0

*Used Equation Coefficients:

V_Batt: 0, 0.01, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)