APRS Track Direct

My position About ☰

reset

VK2GJ-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2GJ-6. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Vbat*	Psys*	Temp*	AirP*
1786715830	4 V	122 mW	24.7 degC	101350 Pa
1786715751	4 V	122 mW	23.2 degC	101362.5 Pa
1786714068	4 V	124 mW	25.4 degC	101375 Pa
1786712186	4 V	336 mW	27.4 degC	101350 Pa
1786712152	4 V	224 mW	27.2 degC	101362.5 Pa
1786710403	4 V	116 mW	23.4 degC	101350 Pa
1786708592	4 V	114 mW	23.3 degC	101350 Pa
1786708553	4 V	112 mW	22.7 degC	101337.5 Pa
1786706782	4 V	112 mW	22.7 degC	101325 Pa
1786704989	4 V	114 mW	23.1 degC	101287.5 Pa
1786704954	4 V	114 mW	22.7 degC	101287.5 Pa
1786703188	4.01 V	114 mW	23 degC	101262.5 Pa
1786701384	4 V	334 mW	27.2 degC	101225 Pa
1786701356	4 V	226 mW	27.2 degC	101225 Pa
1786699587	4 V	116 mW	22.8 degC	101212.5 Pa
1786697788	4 V	114 mW	23 degC	101175 Pa
1786697752	4.01 V	112 mW	22.5 degC	101187.5 Pa
1786695981	3.99 V	112 mW	22.8 degC	101137.5 Pa
1786694182	4 V	114 mW	22.5 degC	101100 Pa
1786694158	4 V	228 mW	22.3 degC	101112.5 Pa
1786692385	3.99 V	336 mW	26.7 degC	101062.5 Pa
1786690594	4 V	114 mW	22.5 degC	101037.5 Pa
1786690559	4 V	116 mW	22 degC	101050 Pa
1786688814	4 V	120 mW	23 degC	101012.5 Pa
1786686992	4 V	114 mW	22.2 degC	100987.5 Pa

*Used Equation Coefficients:

Vbat: 0, 0.001, 0

Vsol: 0, 0.001, 0

Psys: 0, 2, 0

Temp: 0, 0.1, -100

AirP: 0, 12.5, 500

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)