APRS Track Direct

My position About ☰

reset

OE3PDB-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE3PDB-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Eff1h*	Rx10m*
1786734099	13.11 Volt	570 Pkt	75 Pcnt	76 Pkt
1786730499	13.11 Volt	380 Pkt	63 Pcnt	51 Pkt
1786726899	13.11 Volt	450 Pkt	58 Pcnt	51 Pkt
1786723300	13.11 Volt	390 Pkt	65 Pcnt	48 Pkt
1786719700	13.11 Volt	540 Pkt	78 Pcnt	77 Pkt
1786716100	13.11 Volt	640 Pkt	84 Pcnt	102 Pkt
1786712500	13.11 Volt	740 Pkt	83 Pcnt	96 Pkt
1786708900	13.11 Volt	800 Pkt	80 Pcnt	128 Pkt
1786705300	13.11 Volt	760 Pkt	87 Pcnt	102 Pkt
1786701700	13.11 Volt	710 Pkt	83 Pcnt	110 Pkt
1786698100	13.11 Volt	770 Pkt	83 Pcnt	110 Pkt
1786694500	13.11 Volt	670 Pkt	83 Pcnt	123 Pkt
1786690901	13.11 Volt	850 Pkt	85 Pcnt	118 Pkt
1786687301	13.11 Volt	750 Pkt	89 Pcnt	163 Pkt
1786683701	13.11 Volt	690 Pkt	89 Pcnt	106 Pkt
1786680101	13.11 Volt	670 Pkt	87 Pcnt	115 Pkt
1786676501	13.11 Volt	650 Pkt	83 Pcnt	107 Pkt
1786672901	13.11 Volt	700 Pkt	87 Pcnt	130 Pkt
1786669301	13.11 Volt	610 Pkt	81 Pcnt	89 Pkt
1786662100	13.11 Volt	630 Pkt	90 Pcnt	95 Pkt
1786658500	13.11 Volt	580 Pkt	86 Pcnt	93 Pkt
1786654900	13.11 Volt	610 Pkt	85 Pcnt	79 Pkt
1786651301	13.11 Volt	610 Pkt	93 Pcnt	106 Pkt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Rx10m: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)