APRS Track Direct

My position About ☰

reset

E24SAT-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E24SAT-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1836273893	0 Pkt	-47 dBm	0.57 V
1762321860	1 Pkt	-57 dBm	0.76 V
1762320035	1 Pkt	-58 dBm	0.76 V
1762318209	0 Pkt	-57 dBm	0.78 V
1762316384	1 Pkt	-58 dBm	0.74 V
1762314559	2 Pkt	-55 dBm	0.76 V
1762312733	0 Pkt	-62 dBm	0.86 V
1762310908	2 Pkt	-59 dBm	0.82 V
1762309082	1 Pkt	-61 dBm	0.88 V
1762307257	1 Pkt	-61 dBm	0.78 V
1762305432	0 Pkt	-61 dBm	0.68 V
1762304509	1 Pkt	-58 dBm	0.59 V
1762302683	0 Pkt	-57 dBm	0.76 V
1762300858	1 Pkt	-57 dBm	0.92 V
1762299033	2 Pkt	-60 dBm	1.13 V
1762297208	0 Pkt	-60 dBm	1.23 V
1762295383	0 Pkt	-60 dBm	1.27 V
1762293559	0 Pkt	-60 dBm	1.23 V
1762291732	1 Pkt	-61 dBm	1.17 V
1762289907	0 Pkt	-61 dBm	1.07 V
1762288082	1 Pkt	-60 dBm	1.13 V
1762286256	1 Pkt	-61 dBm	1.05 V
1762284431	3 Pkt	-60 dBm	1.15 V
1762282608	1 Pkt	-60 dBm	1.17 V
1762280780	1 Pkt	-57 dBm	0.64 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)