APRS Track Direct

My position About ☰

reset

UR7D-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object UR7D-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1732294568	13.95 Volt	150 Pkt	50 Pkt	82 Pcnt
1732294268	13.95 Volt	160 Pkt	50 Pkt	81 Pcnt
1732293968	13.95 Volt	150 Pkt	40 Pkt	80 Pcnt
1732293668	13.95 Volt	150 Pkt	50 Pkt	82 Pcnt
1732293368	13.95 Volt	150 Pkt	50 Pkt	80 Pcnt
1732293068	13.95 Volt	150 Pkt	50 Pkt	81 Pcnt
1732292768	13.95 Volt	160 Pkt	50 Pkt	80 Pcnt
1732292468	13.95 Volt	150 Pkt	50 Pkt	81 Pcnt
1732292168	13.95 Volt	150 Pkt	50 Pkt	80 Pcnt
1732291868	13.95 Volt	150 Pkt	50 Pkt	79 Pcnt
1732291568	13.95 Volt	150 Pkt	50 Pkt	78 Pcnt
1732291268	13.95 Volt	150 Pkt	50 Pkt	77 Pcnt
1732290968	13.95 Volt	140 Pkt	50 Pkt	77 Pcnt
1732290668	13.95 Volt	150 Pkt	50 Pkt	79 Pcnt
1732290368	13.95 Volt	150 Pkt	50 Pkt	81 Pcnt
1732290068	13.95 Volt	150 Pkt	50 Pkt	82 Pcnt
1732289768	13.95 Volt	150 Pkt	50 Pkt	82 Pcnt
1732289468	13.95 Volt	150 Pkt	50 Pkt	81 Pcnt
1732289168	13.95 Volt	150 Pkt	50 Pkt	83 Pcnt
1732288868	13.95 Volt	150 Pkt	40 Pkt	82 Pcnt
1732288568	13.95 Volt	150 Pkt	40 Pkt	85 Pcnt
1732288268	13.95 Volt	160 Pkt	40 Pkt	86 Pcnt
1732287968	13.95 Volt	150 Pkt	40 Pkt	86 Pcnt
1732287668	13.95 Volt	160 Pkt	50 Pkt	85 Pcnt
1732287368	13.95 Volt	150 Pkt	50 Pkt	86 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)