APRS Track Direct

My position About ☰

reset

YB2IBO-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YB2IBO-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	TxTraffic*	RSSI*	Voltage*
1782561309	30 Pkt	-80 dBm	0.14 V
1782550292	22 Pkt	-79 dBm	0.12 V
1782532723	6 Pkt	-78 dBm	0.1 V
1782519115	20 Pkt	-74 dBm	0.1 V
1782513534	9 Pkt	-73 dBm	0.14 V
1782513351	284 Pkt	-73 dBm	0.16 V
1782512418	145 Pkt	-72 dBm	0.1 V
1782511454	152 Pkt	-72 dBm	0.16 V
1782510479	269 Pkt	-72 dBm	0.12 V
1782509547	257 Pkt	-73 dBm	0.1 V
1782508616	258 Pkt	-73 dBm	0.12 V
1782507682	268 Pkt	-72 dBm	0.16 V
1782506750	288 Pkt	-73 dBm	0.08 V
1782505819	255 Pkt	-73 dBm	0.08 V
1782504887	245 Pkt	-73 dBm	0.1 V
1782503956	20 Pkt	-72 dBm	0.14 V
1782503196	257 Pkt	-72 dBm	0.1 V
1782502262	256 Pkt	-72 dBm	0.14 V
1782501330	255 Pkt	-73 dBm	0.12 V
1782500397	257 Pkt	-74 dBm	0.14 V
1782499464	10 Pkt	-71 dBm	0.1 V
1782499192	256 Pkt	-73 dBm	0.1 V
1782498259	269 Pkt	-73 dBm	0.12 V
1782497327	287 Pkt	-74 dBm	0.14 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)