APRS Track Direct

My position About ☰

reset

DB0IS Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0IS. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	BATT*	CPU*	CASE*	OUT*
1749329203	24.1 V	58.5 C	26 C	19.3 C
1749328603	24.1 V	59 C	26.5 C	19.3 C
1749328002	24.1 V	57.9 C	26.5 C	19.4 C
1749327401	24.1 V	59 C	26.5 C	19.4 C
1749326801	24.1 V	57.9 C	26.5 C	19.4 C
1749325601	24.1 V	57.9 C	27 C	19.4 C
1749325000	24.2 V	58.5 C	26.5 C	19.4 C
1749324400	24.1 V	59 C	26.5 C	19.5 C
1749323799	24.1 V	57.9 C	26.5 C	19.5 C
1749323198	24.1 V	58.5 C	26.5 C	19.5 C
1749322598	24.1 V	59 C	27 C	19.5 C
1749321998	23.8 V	59 C	26.5 C	19.5 C
1749321397	24.1 V	59 C	27 C	19.5 C
1749320797	24.1 V	59 C	27 C	19.5 C
1749320196	24.1 V	59 C	27 C	19.5 C
1749319596	24.1 V	59 C	27 C	19.5 C
1749318995	24.2 V	59 C	27.5 C	19.5 C
1749318395	24.1 V	59 C	28.5 C	19.6 C
1749317795	24.1 V	59 C	28 C	19.5 C
1749317194	24.2 V	59 C	27.5 C	19.5 C
1749316594	24.1 V	57.9 C	26.5 C	19.5 C
1749315994	24.1 V	58.5 C	26.5 C	19.5 C
1749315394	24.1 V	59 C	26.5 C	19.5 C
1749314793	24.1 V	57.9 C	26.5 C	19.5 C
1749314193	24.1 V	57.9 C	26.5 C	19.5 C

*Used Equation Coefficients:

BATT: 0, 0.1, 0

CPU: 0, 0.1, 0

CASE: 0, 0.1, 0

OUT: 0, 0.1, 0

PA: 0, 0.1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)