APRS Track Direct

My position About ☰

reset

YC1JEL-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YC1JEL-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1782547172	0 Pkt	-55 dBm	18.58 V
1782546849	0 Pkt	-55 dBm	16.57 V
1782546523	0 Pkt	-56 dBm	16.14 V
1782546198	0 Pkt	-57 dBm	13.64 V
1782545878	0 Pkt	-55 dBm	13.84 V
1782545550	0 Pkt	-56 dBm	14.95 V
1782545227	0 Pkt	-55 dBm	15.34 V
1782544903	0 Pkt	-55 dBm	16.12 V
1782544579	0 Pkt	-55 dBm	16.65 V
1782544256	0 Pkt	-54 dBm	16.82 V
1782543932	0 Pkt	-55 dBm	16.55 V
1782543608	0 Pkt	-55 dBm	15.26 V
1782543285	1 Pkt	-54 dBm	16.16 V
1782542962	0 Pkt	-56 dBm	15.5 V
1782542637	0 Pkt	-54 dBm	14.93 V
1782542313	0 Pkt	-55 dBm	15.32 V
1782541991	0 Pkt	-55 dBm	15.91 V
1782541668	0 Pkt	-54 dBm	15.91 V
1782541356	0 Pkt	-55 dBm	16.12 V
1782541019	0 Pkt	-55 dBm	15.91 V
1782540695	0 Pkt	-54 dBm	16.04 V
1782540374	0 Pkt	-54 dBm	15.38 V
1782540049	0 Pkt	-55 dBm	15.59 V
1782539727	0 Pkt	-57 dBm	15.07 V
1782539419	0 Pkt	-55 dBm	14.97 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)