APRS Track Direct

My position About ☰

reset

OK9DOB-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OK9DOB-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vbatt*	PotrubiT*
1786722345	4.12 V	23.9 deg.C
1786721742	4.31 V	23.8 deg.C
1786721136	4.06 V	23.8 deg.C
1786720534	4.17 V	23.7 deg.C
1786719930	4.3 V	23.7 deg.C
1786719325	4.25 V	23.8 deg.C
1786718721	4.17 V	23.7 deg.C
1786718119	4.14 V	23.5 deg.C
1786717513	4.29 V	23.5 deg.C
1786716909	4.07 V	23.6 deg.C
1786716306	4.14 V	23.3 deg.C
1786715700	4.24 V	23.3 deg.C
1786715088	4.22 V	23.3 deg.C
1786714485	4.31 V	23 deg.C
1786713879	4.22 V	22.9 deg.C
1786713276	4.14 V	22.9 deg.C
1786712673	4.22 V	23 deg.C
1786712068	4.26 V	22.8 deg.C
1786711464	4.11 V	22.6 deg.C
1786710861	4.25 V	22.8 deg.C
1786710256	4.24 V	22.5 deg.C
1786709652	4.15 V	22.5 deg.C
1786709049	4.24 V	22.3 deg.C
1786708444	4.17 V	22.4 deg.C
1786707840	4.08 V	22.3 deg.C

*Used Equation Coefficients:

GasCounter: 0, 0.01, 0

Vbatt: 0, 0.01, 0

ExtHum: 0, 1, 0

SysPres: 0, 0.1, 0

PotrubiT: 0, 0.1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)