APRS Track Direct

My position About ☰

reset

YO3FBD-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO3FBD-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp_interioara*	Temp_exterioara*	Temp_TX_RoLink*
1836274744	19.2 C	12.4 C	24.5 C
1836274145	19.8 C	13.4 C	28.8 C
1782500466	31.8 C	25.9 C	33.9 C
1782499871	31.8 C	26.3 C	34.1 C
1782499266	32 C	26.5 C	34.5 C
1782498671	32.4 C	27 C	35 C
1782498071	32.9 C	27.2 C	35.4 C
1782497466	33.5 C	27.6 C	35.9 C
1782496866	34.1 C	27.5 C	36.8 C
1782496272	35.1 C	27.8 C	37.6 C
1782495666	35.9 C	28.6 C	37.9 C
1782495066	35.9 C	28.9 C	38.4 C
1782494471	36.6 C	29.2 C	39.3 C
1782493866	37.4 C	29.9 C	40.3 C
1782493266	38.3 C	30.1 C	41.2 C
1782492671	39.2 C	30.9 C	42.1 C
1782492071	40.4 C	31.3 C	43.1 C
1782491466	41.9 C	31.6 C	44.1 C
1782490871	43.2 C	32.5 C	44.6 C
1782490266	43.2 C	32.8 C	44.8 C
1782489666	43.8 C	32.9 C	45.6 C
1782489071	43.6 C	33.2 C	46.8 C
1782488471	42.9 C	33.4 C	45.9 C
1782487866	43.5 C	33.1 C	44.1 C
1782487271	43.6 C	33.9 C	43.8 C

*Used Equation Coefficients:

Temp_interioara: 0, 1, -100

Temp_exterioara: 0, 1, -100

Temp_TX_RoLink: 0, 1, -100

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)