APRS Track Direct

My position About ☰

reset

SP8EBC-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP8EBC-12. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Rx10min*	Vbatt*	Tempre*
1774074816	60 Pkt	12.72 V	0 DegC
1774074210	59 Pkt	12.74 V	0 DegC
1774073613	60 Pkt	12.64 V	0 DegC
1774073010	59 Pkt	12.74 V	0 DegC
1774072411	60 Pkt	12.74 V	0 DegC
1774071804	59 Pkt	12.72 V	0 DegC
1774071208	60 Pkt	12.74 V	0 DegC
1774070601	59 Pkt	12.78 V	0 DegC
1774070002	59 Pkt	12.74 V	0 DegC
1774069409	60 Pkt	12.72 V	0 DegC
1774068799	59 Pkt	12.76 V	0 DegC
1774068203	60 Pkt	12.7 V	0 DegC
1774067597	59 Pkt	12.74 V	0 DegC
1774067000	60 Pkt	12.78 V	0 DegC
1774066394	59 Pkt	12.76 V	0 DegC
1774065801	60 Pkt	12.74 V	0 DegC
1774065191	59 Pkt	12.76 V	0 DegC
1774064595	60 Pkt	12.76 V	0 DegC
1774063989	59 Pkt	12.78 V	0 DegC
1774063393	60 Pkt	12.74 V	0 DegC
1774062786	55 Pkt	10 V	-50 DegC
1774039717	60 Pkt	12.8 V	0 DegC
1774039119	60 Pkt	12.84 V	0 DegC
1774038514	59 Pkt	12.82 V	0 DegC
1774037919	60 Pkt	12.78 V	0 DegC

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Visc10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)