APRS Track Direct

My position About ☰

reset

OE8KKK-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE8KKK-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	U BATCd*	TempT*	Rx 1h*	Ef 1h*
1732292244	13.7 V	16.5 C	10 Pkt	43 Pct
1732291943	13.7 V	16.5 C	10 Pkt	37 Pct
1732291643	13.7 V	16.5 C	10 Pkt	41 Pct
1732291343	13.7 V	16.5 C	10 Pkt	41 Pct
1732291043	13.7 V	16.5 C	10 Pkt	40 Pct
1732290742	13.7 V	16.5 C	10 Pkt	42 Pct
1732290442	13.7 V	16.5 C	10 Pkt	37 Pct
1732290142	13.7 V	16.5 C	10 Pkt	36 Pct
1732289841	13.7 V	16.5 C	10 Pkt	37 Pct
1732289541	13.7 V	16.5 C	10 Pkt	41 Pct
1732289241	13.7 V	16.5 C	10 Pkt	39 Pct
1732288940	13.7 V	17 C	10 Pkt	41 Pct
1732288640	13.7 V	17 C	10 Pkt	54 Pct
1732288340	13.7 V	17 C	10 Pkt	58 Pct
1732288040	13.7 V	17 C	10 Pkt	52 Pct
1732287739	13.7 V	17 C	10 Pkt	58 Pct
1732287439	13.7 V	17 C	10 Pkt	60 Pct
1732287139	13.7 V	17 C	10 Pkt	63 Pct
1732286838	13.7 V	17.5 C	10 Pkt	65 Pct
1732286538	13.7 V	17.5 C	10 Pkt	72 Pct
1732286238	13.7 V	17.5 C	10 Pkt	73 Pct
1732285938	13.7 V	17.5 C	10 Pkt	71 Pct
1732285637	13.7 V	17.5 C	10 Pkt	72 Pct
1732285337	13.7 V	17.5 C	10 Pkt	63 Pct
1732285037	13.7 V	18 C	10 Pkt	65 Pct

*Used Equation Coefficients:

I Solar: 0, 0.1687, -21.4241

U BATCd: 0, 0.1, 0

TempT: 0, 0.5, -64

Rx 1h: 0, 10, 0

Ef 1h: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)