APRS Track Direct

My position About ☰

reset

K0WHW-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object K0WHW-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	DigiRpt*	Temp*
1774131710	2 Pkts	2 Pkts	0 Pkts	18 C
1774128110	2 Pkts	2 Pkts	0 Pkts	19 C
1774124510	5 Pkts	2 Pkts	0 Pkts	18 C
1774120910	4 Pkts	4 Pkts	0 Pkts	15 C
1774117310	2 Pkts	2 Pkts	0 Pkts	10 C
1774113710	2 Pkts	2 Pkts	0 Pkts	4 C
1774110110	17 Pkts	16 Pkts	4 Pkts	5 C
1774106510	43 Pkts	40 Pkts	12 Pkts	4 C
1774102910	47 Pkts	46 Pkts	40 Pkts	2 C
1774099311	12 Pkts	12 Pkts	10 Pkts	1 C
1774095709	10 Pkts	9 Pkts	2 Pkts	1 C
1774092109	4 Pkts	3 Pkts	1 Pkts	0 C
1774088509	2 Pkts	1 Pkts	0 Pkts	1 C
1774084909	6 Pkts	4 Pkts	2 Pkts	1 C
1774081309	2 Pkts	2 Pkts	0 Pkts	1 C
1774077709	0 Pkts	0 Pkts	0 Pkts	1 C
1774074109	3 Pkts	1 Pkts	0 Pkts	2 C
1774070509	6 Pkts	6 Pkts	1 Pkts	2 C
1774066911	7 Pkts	6 Pkts	0 Pkts	4 C
1774063309	4 Pkts	4 Pkts	0 Pkts	4 C
1774059709	4 Pkts	4 Pkts	0 Pkts	5 C
1774056109	3 Pkts	2 Pkts	0 Pkts	5 C
1774052509	5 Pkts	5 Pkts	1 Pkts	6 C
1774048909	11 Pkts	11 Pkts	0 Pkts	9 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)