APRS Track Direct

My position About ☰

reset

SPRFLD Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SPRFLD. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx1h*	Rx10m*	Temp*	Vin*
1790639556	510 Pkt	105 Pkt	63.7 F	13.69 Volt
1790639256	500 Pkt	96 Pkt	63.7 F	13.69 Volt
1790638956	500 Pkt	91 Pkt	63.7 F	13.69 Volt
1790638656	490 Pkt	69 Pkt	63.7 F	13.69 Volt
1790638356	500 Pkt	66 Pkt	63.7 F	13.69 Volt
1790638056	490 Pkt	72 Pkt	63.7 F	13.69 Volt
1790637756	500 Pkt	75 Pkt	63.7 F	13.69 Volt
1790637456	500 Pkt	57 Pkt	63.7 F	13.69 Volt
1790637156	510 Pkt	59 Pkt	62.8 F	13.69 Volt
1790636857	500 Pkt	77 Pkt	62.8 F	13.69 Volt
1790636556	510 Pkt	82 Pkt	62.8 F	13.69 Volt
1790636256	500 Pkt	86 Pkt	62.8 F	13.69 Volt
1790635956	490 Pkt	95 Pkt	62.8 F	13.69 Volt
1790635657	480 Pkt	81 Pkt	62.8 F	13.69 Volt
1790635357	470 Pkt	88 Pkt	61.9 F	13.69 Volt
1790635056	460 Pkt	75 Pkt	61.9 F	13.69 Volt
1790634757	460 Pkt	71 Pkt	61.9 F	13.69 Volt
1790634457	470 Pkt	71 Pkt	61.9 F	13.69 Volt
1790634157	460 Pkt	83 Pkt	61.9 F	13.69 Volt
1790633857	480 Pkt	61 Pkt	61.9 F	13.69 Volt
1790633557	470 Pkt	66 Pkt	61 F	13.69 Volt
1790633263	480 Pkt	71 Pkt	61 F	13.69 Volt
1790632957	490 Pkt	65 Pkt	61 F	13.69 Volt
1790632657	490 Pkt	77 Pkt	61 F	13.69 Volt
1790632357	490 Pkt	69 Pkt	61 F	13.69 Volt

*Used Equation Coefficients:

Rx1h: 0, 10, 0

Rx10m: 0, 1, 0

Dig1h: 0, 10, 0

Temp: 0, 0.9, -83

Vin: 0, 0.07, 0.53

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)