APRS Track Direct

My position About ☰

reset

HS3LSE-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS3LSE-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	RxTraffic*	TxTraffic*	RSSI*
1836274722	8 Pkt	0 Pkt	-62 dBm
1782559109	18 Pkt	0 Pkt	-58 dBm
1782556363	2 Pkt	0 Pkt	-58 dBm
1782553617	3 Pkt	0 Pkt	-56 dBm
1782550869	1 Pkt	0 Pkt	-57 dBm
1782548123	3 Pkt	0 Pkt	-57 dBm
1782545376	2 Pkt	0 Pkt	-57 dBm
1782542629	3 Pkt	0 Pkt	-56 dBm
1782539882	2 Pkt	0 Pkt	-57 dBm
1782537136	2 Pkt	0 Pkt	-58 dBm
1782534388	2 Pkt	0 Pkt	-57 dBm
1782531641	3 Pkt	0 Pkt	-57 dBm
1782528894	2 Pkt	0 Pkt	-56 dBm
1782526147	3 Pkt	0 Pkt	-56 dBm
1782523400	2 Pkt	0 Pkt	-57 dBm
1782520653	3 Pkt	0 Pkt	-56 dBm
1782517907	2 Pkt	0 Pkt	-58 dBm
1782515160	4 Pkt	0 Pkt	-57 dBm
1782512413	1 Pkt	0 Pkt	-58 dBm
1782509667	3 Pkt	1 Pkt	-58 dBm
1782506920	2 Pkt	0 Pkt	-58 dBm
1782504173	3 Pkt	1 Pkt	-57 dBm
1782501427	3 Pkt	2 Pkt	-59 dBm
1782498680	3 Pkt	0 Pkt	-59 dBm
1782495933	3 Pkt	0 Pkt	-59 dBm

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)