APRS Track Direct

My position About ☰

reset

ED7YAX-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED7YAX-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	VAPRS*	Carga*	Trepe*	Taprs*
1753738399	14.43 Volt	78 mA	-64 C	29.5 C
1753738100	14.43 Volt	58.5 mA	-64 C	29.5 C
1753737799	14.5 Volt	58.5 mA	-64 C	29.5 C
1753737500	14.43 Volt	97.5 mA	-64 C	29 C
1753737199	14.43 Volt	39 mA	-64 C	29 C
1753736899	14.5 Volt	78 mA	-64 C	29 C
1753736599	14.43 Volt	78 mA	-64 C	29 C
1753736299	14.43 Volt	58.5 mA	-64 C	29 C
1753735999	14.5 Volt	39 mA	-64 C	29 C
1753735699	14.43 Volt	117 mA	-64 C	29 C
1753735399	14.43 Volt	58.5 mA	-64 C	29 C
1753735099	14.43 Volt	58.5 mA	-64 C	29 C
1753734801	14.5 Volt	78 mA	-64 C	29 C
1753734499	14.43 Volt	58.5 mA	-64 C	29 C
1753734199	14.43 Volt	39 mA	-64 C	29 C
1753733900	13.76 Volt	117 mA	-64 C	29 C
1753733600	14.43 Volt	58.5 mA	-64 C	29 C
1753733299	14.43 Volt	58.5 mA	-64 C	29 C
1753733000	14.5 Volt	78 mA	-64 C	29 C
1753732699	14.43 Volt	58.5 mA	-64 C	29 C
1753732400	14.5 Volt	58.5 mA	-64 C	29 C
1753732100	14.06 Volt	117 mA	-64 C	28.5 C
1753731800	14.43 Volt	39 mA	-64 C	28.5 C
1753731500	14.43 Volt	58.5 mA	-64 C	28.5 C
1753731200	14.5 Volt	78 mA	-64 C	28.5 C

*Used Equation Coefficients:

VAPRS: 0, 0.074, 0

VREPE: 0, 0.074, 0

Carga: 0, 19.5, -2496

Trepe: 0, 0.5, -64

Taprs: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)