APRS Track Direct

My position About ☰

reset

TA2KE-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA2KE-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1774088187	20 Pkt	-32 dBm	12.33 V
1774088047	113 Pkt	-32 dBm	12.33 V
1774087615	21 Pkt	-32 dBm	12.33 V
1774087479	124 Pkt	-33 dBm	12.22 V
1774087038	94 Pkt	-33 dBm	12.33 V
1774086623	23 Pkt	-31 dBm	12.33 V
1774086462	122 Pkt	-31 dBm	12.22 V
1774086024	94 Pkt	-32 dBm	12.22 V
1774085616	15 Pkt	-31 dBm	12.22 V
1774085337	121 Pkt	-32 dBm	12.22 V
1774084904	121 Pkt	-30 dBm	12.33 V
1774084468	123 Pkt	-32 dBm	12.22 V
1774084033	122 Pkt	-33 dBm	12.22 V
1774082655	18 Pkt	-33 dBm	12.2 V
1774082223	122 Pkt	-31 dBm	12.22 V
1774081672	24 Pkt	-32 dBm	12.2 V
1774081096	105 Pkt	-32 dBm	12.22 V
1774080677	17 Pkt	-32 dBm	12.33 V
1774080149	108 Pkt	-30 dBm	12.33 V
1774079546	23 Pkt	-32 dBm	12.22 V
1774079225	105 Pkt	-34 dBm	12.33 V
1774078796	26 Pkt	-30 dBm	12.22 V
1774078282	112 Pkt	-32 dBm	12.33 V
1774077848	25 Pkt	-30 dBm	12.22 V
1774077330	102 Pkt	-33 dBm	12.22 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)