APRS Track Direct

My position About ☰

reset

E29JAU-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E29JAU-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1790673929	0 Pkt	31 dBm	0.06 V
1790673606	1 Pkt	31 dBm	0.06 V
1790673282	0 Pkt	31 dBm	0.06 V
1790672958	1 Pkt	31 dBm	0.06 V
1790672635	0 Pkt	31 dBm	0.06 V
1790672312	1 Pkt	31 dBm	0.06 V
1790671988	0 Pkt	31 dBm	0.06 V
1790671665	1 Pkt	31 dBm	0.06 V
1790671342	0 Pkt	31 dBm	0.06 V
1790671017	0 Pkt	31 dBm	0.06 V
1790670693	0 Pkt	31 dBm	0.06 V
1790670044	1 Pkt	31 dBm	0.06 V
1790669720	0 Pkt	31 dBm	0.06 V
1790669396	1 Pkt	31 dBm	0.06 V
1790669072	0 Pkt	31 dBm	0.06 V
1790668748	1 Pkt	31 dBm	0.04 V
1790668425	0 Pkt	31 dBm	0.06 V
1790668101	1 Pkt	31 dBm	0.06 V
1790667777	0 Pkt	31 dBm	0.06 V
1790667454	1 Pkt	31 dBm	0.06 V
1790667130	0 Pkt	31 dBm	0.06 V
1790666807	0 Pkt	31 dBm	0.06 V
1790666484	0 Pkt	31 dBm	0.06 V
1790666161	1 Pkt	31 dBm	0.06 V
1790665836	0 Pkt	31 dBm	0.06 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)