APRS Track Direct

My position About ☰

reset

SR0L Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR0L. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	MaxLsb*	MaxMsb*	LastTempr*	Vbatt*
1790673032	18 Raw	28 Raw	7.75 DegC	14.3 V
1790666113	159 Raw	27 Raw	3.5 DegC	13.18 V
1790665484	138 Raw	27 Raw	2.75 DegC	13.18 V
1790664231	88 Raw	27 Raw	1 DegC	13.16 V
1790663602	91 Raw	27 Raw	1 DegC	13.2 V
1790661707	203 Raw	26 Raw	23.75 DegC	13.18 V
1790659824	115 Raw	26 Raw	23.75 DegC	13.2 V
1790659195	111 Raw	26 Raw	23.75 DegC	13.16 V
1790657941	108 Raw	26 Raw	23.75 DegC	13.08 V
1790650389	125 Raw	26 Raw	23.75 DegC	13.2 V
1790649135	136 Raw	26 Raw	23.75 DegC	13.18 V
1790647248	135 Raw	26 Raw	23.75 DegC	13.16 V
1790645990	140 Raw	26 Raw	23.75 DegC	13.22 V
1790644736	149 Raw	26 Raw	23.75 DegC	13.16 V
1790642221	161 Raw	26 Raw	23.75 DegC	13.18 V
1790639696	182 Raw	26 Raw	23.75 DegC	13.22 V
1790638442	174 Raw	26 Raw	23.75 DegC	13.2 V
1790637814	174 Raw	26 Raw	23.75 DegC	13.22 V
1790635302	202 Raw	26 Raw	23.75 DegC	13.2 V
1790634673	211 Raw	26 Raw	23.75 DegC	13.2 V
1790634044	204 Raw	26 Raw	23.75 DegC	13.2 V
1790633415	222 Raw	26 Raw	23.75 DegC	13.18 V
1790632158	244 Raw	26 Raw	23.75 DegC	13.2 V
1790626488	175 Raw	27 Raw	4.25 DegC	13.16 V
1790625859	176 Raw	27 Raw	4.25 DegC	13.22 V

*Used Equation Coefficients:

MaxLsb: 0, 1, 0

MaxMsb: 0, 1, 0

LastTempr: 0, 0.25, -40

Vbatt: 0, 0.02, 10

PtSts: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)