APRS Track Direct

My position About ☰

reset

LU6MHO-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU6MHO-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1791737614	3 Pkt	-35 dBm	12.18 V
1791735951	1 Pkt	-37 dBm	12.2 V
1791734288	0 Pkt	-32 dBm	12.2 V
1791732624	0 Pkt	-35 dBm	12.2 V
1791730961	1 Pkt	-37 dBm	12.2 V
1791729297	3 Pkt	-38 dBm	12.2 V
1791727634	5 Pkt	-37 dBm	12.2 V
1791725971	8 Pkt	-36 dBm	12.2 V
1791724308	0 Pkt	-37 dBm	12.2 V
1791722644	1 Pkt	-34 dBm	12.22 V
1791720980	0 Pkt	-36 dBm	12.18 V
1791719317	0 Pkt	-35 dBm	12.2 V
1791717653	0 Pkt	-34 dBm	12.2 V
1791715989	0 Pkt	-35 dBm	12.2 V
1791714326	0 Pkt	-37 dBm	12.18 V
1791712663	0 Pkt	-36 dBm	12.14 V
1791710376	0 Pkt	-35 dBm	12.22 V
1791708714	0 Pkt	-36 dBm	12.2 V
1791707050	0 Pkt	-35 dBm	12.2 V
1791705387	0 Pkt	-34 dBm	12.2 V
1791703724	0 Pkt	-37 dBm	12.2 V
1791702060	0 Pkt	-36 dBm	12.18 V
1791700397	0 Pkt	-36 dBm	12.22 V
1791698734	0 Pkt	-35 dBm	12.2 V
1791697070	0 Pkt	-37 dBm	12.22 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)