APRS Track Direct

My position About ☰

reset

VK5ZX-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK5ZX-5. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Rx 1h*	DEC 1h*	Temp*
1732287764	14.1 Volt	20 Pkt	90 Pcnt	26.5 C
1732285965	14.1 Volt	19 Pkt	90 Pcnt	26.5 C
1732285964	14.1 Volt	19 Pkt	90 Pcnt	26.5 C
1732284164	14.1 Volt	19 Pkt	92 Pcnt	27 C
1732282364	14.1 Volt	18 Pkt	93 Pcnt	27.5 C
1732280564	14.1 Volt	22 Pkt	94 Pcnt	27.5 C
1732278764	14.1 Volt	24 Pkt	92 Pcnt	28 C
1732276964	14.1 Volt	23 Pkt	93 Pcnt	28.5 C
1732275165	14.1 Volt	23 Pkt	94 Pcnt	28.5 C
1732275164	14.1 Volt	23 Pkt	94 Pcnt	28.5 C
1732273364	14.1 Volt	23 Pkt	93 Pcnt	29.5 C
1732271565	14.1 Volt	20 Pkt	93 Pcnt	30 C
1732271564	14.1 Volt	20 Pkt	93 Pcnt	30 C
1732269764	14.1 Volt	27 Pkt	93 Pcnt	31 C
1732267965	14.1 Volt	29 Pkt	94 Pcnt	31.5 C
1732267964	14.1 Volt	29 Pkt	94 Pcnt	31.5 C
1732266164	14.1 Volt	23 Pkt	95 Pcnt	32.5 C
1732264365	14.1 Volt	23 Pkt	97 Pcnt	33 C
1732264365	14.1 Volt	23 Pkt	97 Pcnt	33 C
1732262565	14.1 Volt	23 Pkt	95 Pcnt	33.5 C
1732260765	14.1 Volt	34 Pkt	96 Pcnt	34 C
1732258965	14.1 Volt	42 Pkt	95 Pcnt	34.5 C
1732257165	14.1 Volt	37 Pkt	93 Pcnt	35.5 C
1732255365	14.1 Volt	43 Pkt	90 Pcnt	36.5 C
1732253565	14.1 Volt	38 Pkt	91 Pcnt	36 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx 1h: 0, 1, 0

DIG 1h: 0, 1, 0

DEC 1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)