APRS Track Direct

My position About ☰

reset

LA3SHA-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LA3SHA-15. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Eff1h*	Temp*
1732571631	12.38 Volt	100 Pcnt	2 C
1732569831	12.38 Volt	0 Pcnt	2 C
1732568032	12.38 Volt	0 Pcnt	2 C
1732566232	12.38 Volt	0 Pcnt	2 C
1732564432	12.38 Volt	0 Pcnt	2 C
1732562632	12.38 Volt	0 Pcnt	2 C
1732560832	12.38 Volt	0 Pcnt	2 C
1732559032	12.38 Volt	0 Pcnt	2 C
1732557232	12.38 Volt	0 Pcnt	2.5 C
1732555432	12.38 Volt	0 Pcnt	2.5 C
1732553632	12.38 Volt	0 Pcnt	2 C
1732551832	12.38 Volt	0 Pcnt	2.5 C
1732550032	12.38 Volt	100 Pcnt	2.5 C
1732548232	12.38 Volt	100 Pcnt	3 C
1732546432	12.38 Volt	0 Pcnt	2.5 C
1732544633	12.38 Volt	20 Pcnt	2.5 C
1732542833	12.38 Volt	16 Pcnt	2.5 C
1732541033	12.38 Volt	0 Pcnt	2 C
1732539233	12.38 Volt	50 Pcnt	2.5 C
1732537433	12.38 Volt	33 Pcnt	2.5 C
1732535633	12.45 Volt	0 Pcnt	2 C
1732533833	12.45 Volt	0 Pcnt	1.5 C
1732532033	12.45 Volt	0 Pcnt	1.5 C
1732530233	12.45 Volt	0 Pcnt	1 C
1732528433	12.45 Volt	0 Pcnt	0.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)