APRS Track Direct

My position About ☰

reset

LA3SHA-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LA3SHA-15. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Eff1h*	Temp*
1774644821	12.9 Volt	0 Pcnt	0.5 C
1774643021	12.9 Volt	0 Pcnt	0.5 C
1774641221	12.9 Volt	0 Pcnt	1 C
1774639422	12.9 Volt	0 Pcnt	1 C
1774637622	12.9 Volt	0 Pcnt	0.5 C
1774635822	12.9 Volt	0 Pcnt	0.5 C
1774634022	12.83 Volt	0 Pcnt	0.5 C
1774632222	12.83 Volt	0 Pcnt	1 C
1774630422	12.83 Volt	0 Pcnt	1 C
1774628622	12.9 Volt	0 Pcnt	1.5 C
1774626822	13.05 Volt	0 Pcnt	1.5 C
1774625022	13.13 Volt	20 Pcnt	2 C
1774623224	13.05 Volt	20 Pcnt	3 C
1774621422	13.28 Volt	0 Pcnt	3.5 C
1774619622	13.65 Volt	0 Pcnt	3.5 C
1774617822	14.1 Volt	0 Pcnt	3.5 C
1774616022	13.73 Volt	0 Pcnt	4 C
1774614223	13.8 Volt	0 Pcnt	4.5 C
1774612423	13.88 Volt	0 Pcnt	4.5 C
1774610623	13.88 Volt	0 Pcnt	4 C
1774608823	13.88 Volt	0 Pcnt	4 C
1774607025	13.88 Volt	0 Pcnt	4 C
1774605223	13.88 Volt	0 Pcnt	3 C
1774603423	14.33 Volt	0 Pcnt	2.5 C
1774601683	13.43 Volt	100 Pcnt	2 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)