APRS Track Direct

My position About ☰

reset

SR8WXO Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR8WXO. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*
1754125313	105 Pkt	7 Pkt	5 Pkt
1754124710	108 Pkt	7 Pkt	5 Pkt
1754124108	113 Pkt	10 Pkt	4 Pkt
1754123498	109 Pkt	7 Pkt	5 Pkt
1754122895	129 Pkt	8 Pkt	6 Pkt
1754122292	107 Pkt	5 Pkt	3 Pkt
1754121689	101 Pkt	11 Pkt	5 Pkt
1754121080	123 Pkt	5 Pkt	3 Pkt
1754120477	124 Pkt	7 Pkt	5 Pkt
1754119874	77 Pkt	5 Pkt	3 Pkt
1754119271	117 Pkt	12 Pkt	6 Pkt
1754118661	122 Pkt	6 Pkt	4 Pkt
1754118059	92 Pkt	6 Pkt	4 Pkt
1754117456	112 Pkt	6 Pkt	4 Pkt
1754116853	105 Pkt	8 Pkt	2 Pkt
1754116243	92 Pkt	6 Pkt	4 Pkt
1754115640	96 Pkt	5 Pkt	3 Pkt
1754115038	100 Pkt	4 Pkt	2 Pkt
1754114435	90 Pkt	10 Pkt	4 Pkt
1754113825	89 Pkt	6 Pkt	4 Pkt
1754113222	95 Pkt	6 Pkt	4 Pkt
1754112619	78 Pkt	5 Pkt	3 Pkt
1754112016	84 Pkt	8 Pkt	2 Pkt
1754111407	83 Pkt	5 Pkt	3 Pkt
1754110804	62 Pkt	5 Pkt	3 Pkt

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

HostTx10m: 0, 1, 0

Tempre: 0, 0.25, -25

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)