APRS Track Direct

My position About ☰

reset

VK2RGA-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2RGA-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Battery*	Core*	Tx*
1790633840	12.5 VDC	43.3 degC	31 pkts
1790630241	12.4 VDC	42.3 degC	30 pkts
1790626640	12.3 VDC	40.9 degC	34 pkts
1790623041	12.4 VDC	41.8 degC	32 pkts
1790619441	12.4 VDC	42.3 degC	30 pkts
1790615841	12.5 VDC	42.8 degC	28 pkts
1790612240	12.5 VDC	43.8 degC	31 pkts
1790608641	12.5 VDC	43.8 degC	30 pkts
1790605041	12.4 VDC	44.3 degC	28 pkts
1790601443	12.5 VDC	44.8 degC	30 pkts
1790597840	12.4 VDC	45.2 degC	30 pkts
1790594240	12.6 VDC	47.2 degC	35 pkts
1790590641	12.4 VDC	47.7 degC	36 pkts
1790587041	12.6 VDC	48.2 degC	39 pkts
1790583440	12.6 VDC	49.6 degC	36 pkts
1790579840	13.7 VDC	50.1 degC	27 pkts
1790576241	13.6 VDC	50.6 degC	27 pkts
1790572640	13.7 VDC	49.6 degC	36 pkts
1790569041	13.7 VDC	49.1 degC	61 pkts
1790565442	13.7 VDC	48.2 degC	46 pkts
1790561844	13.7 VDC	47.7 degC	47 pkts
1790558242	14.4 VDC	46.7 degC	34 pkts
1790554641	13.7 VDC	45.2 degC	56 pkts
1790551040	13.2 VDC	43.3 degC	31 pkts

*Used Equation Coefficients:

Battery: 0, 0.1, 0

Core: 0, 0.1, 0

Room: 0, 0.1, 0

Battery: 0, 0.1, 0

Tx: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)