APRS Track Direct

My position About ☰

reset

W3NEP-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W3NEP-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1758200424	13.5 Volt	470 Pkt	200 Pkt	53 Pcnt
1758199523	13.43 Volt	430 Pkt	180 Pkt	54 Pcnt
1758198624	13.5 Volt	460 Pkt	180 Pkt	60 Pcnt
1758196823	13.5 Volt	460 Pkt	220 Pkt	65 Pcnt
1758195923	13.35 Volt	410 Pkt	210 Pkt	64 Pcnt
1758195023	13.5 Volt	380 Pkt	210 Pkt	63 Pcnt
1758194123	13.2 Volt	330 Pkt	200 Pkt	58 Pcnt
1758193224	13.5 Volt	300 Pkt	190 Pkt	56 Pcnt
1758192325	13.5 Volt	310 Pkt	200 Pkt	58 Pcnt
1758191424	13.5 Volt	330 Pkt	210 Pkt	60 Pcnt
1758190524	13.5 Volt	330 Pkt	210 Pkt	59 Pcnt
1758189624	13.5 Volt	320 Pkt	200 Pkt	58 Pcnt
1758188724	13.2 Volt	300 Pkt	190 Pkt	54 Pcnt
1758186924	13.5 Volt	260 Pkt	170 Pkt	53 Pcnt
1758186024	13.5 Volt	270 Pkt	180 Pkt	54 Pcnt
1758185124	13.5 Volt	250 Pkt	170 Pkt	52 Pcnt
1758184224	13.5 Volt	240 Pkt	160 Pkt	51 Pcnt
1758183324	13.5 Volt	240 Pkt	170 Pkt	54 Pcnt
1758182424	13.5 Volt	220 Pkt	170 Pkt	60 Pcnt
1758181526	13.5 Volt	230 Pkt	170 Pkt	67 Pcnt
1758180624	13.5 Volt	240 Pkt	170 Pkt	70 Pcnt
1758179725	13.5 Volt	230 Pkt	160 Pkt	70 Pcnt
1758178824	13.5 Volt	240 Pkt	160 Pkt	69 Pcnt
1758177924	13.5 Volt	230 Pkt	160 Pkt	69 Pcnt
1758177024	13.5 Volt	220 Pkt	150 Pkt	69 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

EffTo: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)