APRS Track Direct

My position About ☰

reset

F6DDS-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F6DDS-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	U*	Rx1h*	Dg1h*	Eff1h*
1786726851	3.23 Volt	330 Pkt	80 Pkt	96 Pcnt
1786726553	0 Volt	330 Pkt	80 Pkt	96 Pcnt
1786726551	0 Volt	330 Pkt	80 Pkt	96 Pcnt
1786726251	16.73 Volt	330 Pkt	80 Pkt	96 Pcnt
1786725951	0 Volt	310 Pkt	70 Pkt	96 Pcnt
1786725651	18.53 Volt	300 Pkt	70 Pkt	96 Pcnt
1786725354	0 Volt	280 Pkt	70 Pkt	95 Pcnt
1786725351	0 Volt	280 Pkt	70 Pkt	95 Pcnt
1786725051	17.48 Volt	300 Pkt	70 Pkt	93 Pcnt
1786724751	0.75 Volt	290 Pkt	70 Pkt	93 Pcnt
1786724451	0 Volt	290 Pkt	60 Pkt	93 Pcnt
1786724153	0.08 Volt	270 Pkt	60 Pkt	93 Pcnt
1786724151	0.08 Volt	270 Pkt	60 Pkt	93 Pcnt
1786723851	0 Volt	270 Pkt	60 Pkt	93 Pcnt
1786723555	0 Volt	270 Pkt	60 Pkt	93 Pcnt
1786723551	0 Volt	270 Pkt	60 Pkt	93 Pcnt
1786723251	0 Volt	280 Pkt	70 Pkt	93 Pcnt
1786722954	9.15 Volt	270 Pkt	60 Pkt	93 Pcnt
1786722951	9.15 Volt	270 Pkt	60 Pkt	93 Pcnt
1786722651	0 Volt	270 Pkt	60 Pkt	92 Pcnt
1786722351	5.33 Volt	260 Pkt	60 Pkt	92 Pcnt
1786722051	18.75 Volt	280 Pkt	60 Pkt	92 Pcnt
1786721753	7.88 Volt	270 Pkt	60 Pkt	94 Pcnt
1786721751	7.88 Volt	270 Pkt	60 Pkt	94 Pcnt
1786721451	12.68 Volt	270 Pkt	60 Pkt	95 Pcnt

*Used Equation Coefficients:

U: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)