APRS Track Direct

My position About ☰

reset

TA3KRT-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA3KRT-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RF->INET*	AllCount*	AllDrop*
1836274258	0 Pkts	48 Pkts	4 Pkts
1836274108	5 Pkts	61 Pkts	4 Pkts
1774747441	2 Pkts	118 Pkts	64 Pkts
1774746852	4 Pkts	109 Pkts	54 Pkts
1774746241	0 Pkts	106 Pkts	76 Pkts
1774745634	3 Pkts	105 Pkts	52 Pkts
1774745035	0 Pkts	121 Pkts	85 Pkts
1774744436	3 Pkts	107 Pkts	54 Pkts
1774743842	5 Pkts	128 Pkts	73 Pkts
1774743234	0 Pkts	106 Pkts	68 Pkts
1774742648	5 Pkts	126 Pkts	80 Pkts
1774742041	0 Pkts	102 Pkts	68 Pkts
1774741434	4 Pkts	113 Pkts	71 Pkts
1774740837	2 Pkts	112 Pkts	54 Pkts
1774740234	0 Pkts	108 Pkts	68 Pkts
1774739644	4 Pkts	113 Pkts	62 Pkts
1774739034	0 Pkts	116 Pkts	75 Pkts
1774738438	5 Pkts	125 Pkts	67 Pkts
1774737841	4 Pkts	117 Pkts	66 Pkts
1774737255	0 Pkts	124 Pkts	81 Pkts
1774736634	3 Pkts	100 Pkts	61 Pkts
1774736034	0 Pkts	109 Pkts	74 Pkts
1774735434	8 Pkts	131 Pkts	74 Pkts
1774734834	4 Pkts	123 Pkts	71 Pkts
1774734234	0 Pkts	112 Pkts	82 Pkts

*Used Equation Coefficients:

RF->INET: 0, 1, 0

INET->RF: 0, 1, 0

RF->RF: 0, 1, 0

AllCount: 0, 1, 0

AllDrop: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)