APRS Track Direct

My position About ☰

reset

SM0PQB-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SM0PQB-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Temp*	Rx10m*	Eff1h*
1836274621	12.23 Volt	32.5 C	0 Pkt	100 %
1836274471	12.3 Volt	32.5 C	0 Pkt	100 %
1836274321	12.23 Volt	32.5 C	0 Pkt	100 %
1836274171	12.23 Volt	32.5 C	0 Pkt	100 %
1836274021	12.23 Volt	32.5 C	0 Pkt	100 %
1778033003	11.7 Volt	26 C	5 Pkt	57 %
1778032703	11.7 Volt	26 C	2 Pkt	50 %
1778032403	11.7 Volt	26 C	0 Pkt	50 %
1778032103	11.7 Volt	26 C	0 Pkt	46 %
1778031803	11.7 Volt	26 C	0 Pkt	53 %
1778031503	11.7 Volt	26 C	2 Pkt	64 %
1778031203	11.7 Volt	26 C	2 Pkt	66 %
1778030903	11.7 Volt	26 C	0 Pkt	66 %
1778030603	11.78 Volt	26 C	0 Pkt	76 %
1778030303	11.78 Volt	26 C	1 Pkt	78 %
1778030003	11.7 Volt	26.5 C	1 Pkt	85 %
1778029703	11.7 Volt	26.5 C	2 Pkt	75 %
1778029403	11.78 Volt	26.5 C	4 Pkt	52 %
1778029103	11.78 Volt	26.5 C	2 Pkt	40 %
1778028803	11.7 Volt	26.5 C	0 Pkt	35 %
1778028503	11.7 Volt	26.5 C	2 Pkt	31 %
1778028203	11.63 Volt	26.5 C	3 Pkt	29 %
1778027903	11.7 Volt	26.5 C	3 Pkt	26 %
1778027603	11.7 Volt	26.5 C	2 Pkt	22 %
1778027303	11.7 Volt	26.5 C	1 Pkt	22 %

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Temp: 0, 0.5, -64

Temp2: 0, 0.5, -64

Rx10m: 0, 1, 0

Eff1h: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)