APRS Track Direct

My position About ☰

reset

LU3QDF-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU3QDF-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	RxTraffic*	RSSI*	Voltage*
1779767698	3 Pkt	-83 dBm	9.6 V
1779766775	0 Pkt	-85 dBm	9.56 V
1779765853	4 Pkt	-84 dBm	9.56 V
1779764930	0 Pkt	-84 dBm	9.52 V
1779764008	3 Pkt	-86 dBm	9.54 V
1779763085	0 Pkt	-86 dBm	9.54 V
1779762163	4 Pkt	-85 dBm	9.52 V
1779761241	0 Pkt	-82 dBm	9.6 V
1779760319	4 Pkt	-78 dBm	9.6 V
1779759396	0 Pkt	-81 dBm	9.6 V
1779758474	5 Pkt	-82 dBm	9.6 V
1779757557	0 Pkt	-83 dBm	9.47 V
1779756629	4 Pkt	-85 dBm	9.52 V
1779754698	0 Pkt	-84 dBm	9.5 V
1779753811	6 Pkt	-78 dBm	9.52 V
1779752886	13 Pkt	-76 dBm	9.56 V
1779751962	5 Pkt	-75 dBm	9.56 V
1779751039	13 Pkt	-79 dBm	9.6 V
1779750115	4 Pkt	-75 dBm	9.52 V
1779749905	12 Pkt	-77 dBm	9.62 V
1779749624	49 Pkt	-78 dBm	9.47 V
1779748690	28 Pkt	-79 dBm	9.56 V
1779747766	2 Pkt	-74 dBm	9.56 V
1779747328	9 Pkt	-77 dBm	9.6 V
1779746407	7 Pkt	-74 dBm	9.6 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)