APRS Track Direct

My position About ☰

reset

AI6KG-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object AI6KG-12. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	SoC*	V*	I*
1762291197	87.65 %	11.98 V	1.02 A
1762291181	81.21 %	12.49 V	0.9 A
1762291166	89.34 %	12.23 V	1.01 A
1762291151	91.46 %	12.1 V	1.12 A
1762291136	81.2 %	12.12 V	0.95 A
1762291121	86.89 %	12.01 V	1.06 A
1762291108	93.08 %	12.13 V	0.98 A
1762291091	87.5 %	12.29 V	1.18 A
1762291077	93.68 %	12.4 V	0.87 A
1762291061	85.49 %	11.99 V	0.85 A
1762291046	89.53 %	12.46 V	1.09 A
1762291032	94.79 %	12.44 V	1.15 A
1762291016	85.25 %	12.19 V	0.81 A
1762291001	89.79 %	12.41 V	1.02 A
1762290987	92.26 %	12.15 V	0.8 A
1762290971	91.94 %	12.48 V	0.87 A
1762290956	86.04 %	12.26 V	0.93 A
1762290941	92.57 %	11.97 V	0.89 A
1762290926	86.42 %	12.01 V	1.09 A
1762290911	89.88 %	12.43 V	1.2 A
1762290896	88.9 %	12.48 V	1.05 A
1762290882	89.28 %	12.28 V	0.92 A
1762290866	90.02 %	12.47 V	1.09 A
1762290852	88.72 %	12.16 V	1.1 A
1762290836	87.82 %	12.25 V	0.95 A

*Used Equation Coefficients:

SoC: 0, 1, 0

V: 0, 1, 0

I: 0, 1, 0

NA: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)