APRS Track Direct

My position About ☰

reset

BM6HFL-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM6HFL-5. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1790652845	35.6 C	4 p	7 p	1222 p
1790651645	35.9 C	2 p	8 p	1218 p
1790650444	35.9 C	1 p	20 p	1221 p
1790649245	35.5 C	5 p	33 p	1256 p
1790648044	35.9 C	14 p	39 p	1267 p
1790646845	35.5 C	14 p	42 p	1268 p
1790645645	35.2 C	11 p	39 p	1275 p
1790644445	35.9 C	17 p	42 p	1299 p
1790643245	35 C	11 p	45 p	1300 p
1790642045	35.4 C	14 p	54 p	1310 p
1790640844	35.2 C	20 p	58 p	1317 p
1790639645	34.6 C	20 p	50 p	1321 p
1790638445	34.8 C	18 p	36 p	1322 p
1790637244	35 C	12 p	34 p	1323 p
1790636045	34.6 C	6 p	46 p	1330 p
1790634845	33.7 C	16 p	53 p	1337 p
1790633645	34.6 C	24 p	51 p	1344 p
1790632445	33.7 C	13 p	44 p	1341 p
1790631245	34.4 C	14 p	51 p	1345 p
1790630045	34.4 C	17 p	56 p	1343 p
1790628845	33.6 C	20 p	58 p	1345 p
1790627645	34 C	19 p	50 p	1346 p
1790626444	34.5 C	19 p	50 p	1347 p
1790625245	33.3 C	12 p	50 p	1342 p
1790624045	33.7 C	19 p	49 p	1343 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)