APRS Track Direct

My position About ☰

reset

YO3KXL-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO3KXL-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	T_ext*	T_int*	T_rad*
1749309671	33.5 C	33.2 C	36.9 C
1749309072	32.9 C	33.1 C	37.6 C
1749308472	33.4 C	33.6 C	41.4 C
1749307871	34.2 C	34.1 C	41.3 C
1749307271	33.8 C	34.3 C	50 C
1749306672	34.5 C	34.8 C	60.4 C
1749306071	33.6 C	34.5 C	55.1 C
1749305471	33.9 C	34.1 C	39.7 C
1749304871	34.3 C	34.9 C	48.2 C
1749304272	34.9 C	34.8 C	37.9 C
1749303671	33.7 C	34.4 C	38.1 C
1749303071	33.8 C	34.3 C	38.9 C
1749302471	34.9 C	35.6 C	38.7 C
1749301872	34.9 C	35.5 C	39.2 C
1749301272	35.2 C	35.8 C	40.6 C
1749300671	34.6 C	35.2 C	42.9 C
1749300071	34.9 C	34.6 C	51.3 C
1749299472	33.1 C	33.9 C	44.6 C
1749298872	32.6 C	33.4 C	37.4 C
1749298271	33.9 C	34.6 C	38.5 C
1749297671	36.1 C	35.8 C	39.8 C
1749297071	36.5 C	35.9 C	38.8 C
1749296472	34.6 C	34 C	38.8 C
1749295872	33.4 C	34 C	41.8 C
1749295271	33.9 C	34.9 C	52.1 C

*Used Equation Coefficients:

T_ext: 0, 1, -100

T_int: 0, 1, -100

T_rad: 0, 1, -100

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)