APRS Track Direct

My position About ☰

reset

AI0ET-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object AI0ET-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vaux*	Vmain*	Pi_temp*
1786658838	13.93 Volts	0.01 Volts	51 Deg.C
1786658826	13.96 Volts	0.01 Volts	50 Deg.C
1786658795	14 Volts	0.01 Volts	50 Deg.C
1786658759	13.96 Volts	0.01 Volts	50 Deg.C
1786658738	13.92 Volts	0.01 Volts	50 Deg.C
1786658717	13.95 Volts	0.01 Volts	50 Deg.C
1786658666	13.96 Volts	0.01 Volts	51 Deg.C
1786658644	13.96 Volts	0.01 Volts	50 Deg.C
1786658633	13.93 Volts	0.02 Volts	51 Deg.C
1786658583	13.96 Volts	0.01 Volts	50 Deg.C
1786658540	14.06 Volts	0.01 Volts	50 Deg.C
1786658510	13.96 Volts	0.01 Volts	50 Deg.C
1786658499	13.96 Volts	0.01 Volts	50 Deg.C
1786658488	13.95 Volts	0.02 Volts	50 Deg.C
1786658466	12.27 Volts	0.01 Volts	51 Deg.C
1786658436	12.27 Volts	0.01 Volts	50 Deg.C
1786658406	12.28 Volts	0.02 Volts	50 Deg.C
1786658377	12.28 Volts	0 Volts	50 Deg.C
1786658346	12.29 Volts	0.01 Volts	50 Deg.C
1786658317	12.3 Volts	0.01 Volts	51 Deg.C
1786658287	12.28 Volts	0.01 Volts	50 Deg.C
1786658257	12.31 Volts	0.02 Volts	50 Deg.C
1786658227	12.31 Volts	0.02 Volts	50 Deg.C
1786658197	12.31 Volts	0.01 Volts	50 Deg.C
1786658166	12.31 Volts	0.01 Volts	51 Deg.C

*Used Equation Coefficients:

Vaux: 0, 0.01, 0

Vmain: 0, 0.01, 0

Pi_temp: 0, 1, 0

Value4: 0, 0, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)