APRS Track Direct

My position About ☰

reset

YB8VK-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YB8VK-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1778068630	0 Pkt	-79 dBm	0.55 V
1778068308	0 Pkt	-77 dBm	0.04 V
1778067986	1 Pkt	-76 dBm	0.18 V
1778067664	0 Pkt	-77 dBm	0.45 V
1778067342	0 Pkt	-77 dBm	0.29 V
1778067020	1 Pkt	-77 dBm	0.29 V
1778066698	0 Pkt	-77 dBm	0.12 V
1778066376	0 Pkt	-77 dBm	0.31 V
1778066054	0 Pkt	-77 dBm	0.7 V
1778065732	0 Pkt	-77 dBm	0.57 V
1778065410	0 Pkt	-77 dBm	0.18 V
1778065088	0 Pkt	-77 dBm	0.29 V
1778064766	1 Pkt	-77 dBm	0.33 V
1778064444	0 Pkt	-77 dBm	0.43 V
1778064122	2 Pkt	-77 dBm	0.04 V
1778063800	1 Pkt	-78 dBm	0.25 V
1778063478	0 Pkt	-78 dBm	0.27 V
1778063156	0 Pkt	-77 dBm	0.31 V
1778062834	0 Pkt	-78 dBm	0.33 V
1778062512	0 Pkt	-77 dBm	0.39 V
1778062190	0 Pkt	-77 dBm	0.37 V
1778061868	0 Pkt	-78 dBm	0.08 V
1778061546	0 Pkt	-77 dBm	0.43 V
1778061224	1 Pkt	-78 dBm	0.14 V
1778060902	0 Pkt	-78 dBm	0.06 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)