APRS Track Direct

My position About ☰

reset

ED1YAP-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED1YAP-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Plant*	Temp*
1773671686	14.1 Volt	14.1 Volt	10 Cº
1773670786	14.1 Volt	14.1 Volt	9.5 Cº
1773669886	14.1 Volt	14.2 Volt	9.5 Cº
1773667186	14.1 Volt	14.2 Volt	8 Cº
1773666286	14.6 Volt	14.7 Volt	8 Cº
1773665386	14.6 Volt	14.7 Volt	8 Cº
1773664488	14.6 Volt	14.7 Volt	7.5 Cº
1773662687	14.7 Volt	14.7 Volt	7 Cº
1773661787	14.7 Volt	14.7 Volt	7 Cº
1773660887	14.7 Volt	14.7 Volt	6.5 Cº
1773659987	14.7 Volt	14.7 Volt	6.5 Cº
1773659089	14.7 Volt	14.7 Volt	6.5 Cº
1773658187	13.2 Volt	13.2 Volt	6 Cº
1773657288	13.2 Volt	13.3 Volt	6 Cº
1773656395	13.6 Volt	13.6 Volt	5.5 Cº
1773655488	13.9 Volt	13.9 Volt	5.5 Cº
1773654588	13.8 Volt	13.8 Volt	5.5 Cº
1773653689	13.8 Volt	13.8 Volt	5 Cº
1773652788	13.6 Volt	13.6 Volt	5 Cº
1773651888	13.5 Volt	13.5 Volt	5 Cº
1773650988	13.4 Volt	13.4 Volt	4.5 Cº
1773650088	13.3 Volt	13.3 Volt	4.5 Cº
1773649188	13.1 Volt	13.1 Volt	4.5 Cº
1773648288	12.9 Volt	12.9 Volt	4.5 Cº
1773647388	12.7 Volt	12.8 Volt	4.5 Cº

*Used Equation Coefficients:

Battery: 0, 0.1, 0

Plant: 0, 0.1, 0

Charge: 0, 0.195, 0

Load: 0, 0.195, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)