APRS Track Direct

My position About ☰

reset

SP2ROC-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP2ROC-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	RPM*	VBAT*	TEMP*	MTH*
1779790116	846 rpm	12.76 V	68 degC	44 h
1779790086	761 rpm	12.82 V	68 degC	44 h
1779790056	761 rpm	12.82 V	68 degC	44 h
1779790026	758 rpm	12.82 V	68 degC	44 h
1779789996	760 rpm	12.82 V	68 degC	44 h
1779789966	759 rpm	12.82 V	68 degC	44 h
1779789906	761 rpm	12.82 V	68 degC	44 h
1779789876	762 rpm	12.82 V	68 degC	44 h
1779789846	760 rpm	12.82 V	68 degC	44 h
1779789816	758 rpm	12.82 V	68 degC	44 h
1779789786	759 rpm	12.82 V	68 degC	44 h
1779789756	759 rpm	12.82 V	68 degC	44 h
1779789726	762 rpm	12.82 V	68 degC	44 h
1779789696	759 rpm	12.82 V	68 degC	44 h
1779789666	759 rpm	12.82 V	68 degC	44 h
1779789636	759 rpm	12.76 V	68 degC	44 h
1779789606	758 rpm	12.76 V	68 degC	44 h
1779789516	759 rpm	12.82 V	68 degC	43 h
1779789486	760 rpm	12.81 V	68 degC	43 h
1779789456	758 rpm	12.82 V	68 degC	43 h
1779789426	761 rpm	12.82 V	68 degC	43 h
1779789396	762 rpm	12.76 V	68 degC	43 h
1779789366	762 rpm	12.76 V	68 degC	43 h
1779789336	760 rpm	12.82 V	67 degC	43 h
1779789306	760 rpm	12.76 V	67 degC	43 h

*Used Equation Coefficients:

RPM: 0, 1, 0

VBAT: 0, 0.01, 0

TEMP: 0, 1, -100

TRIP: 0, 0.1, 0

MTH: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)