APRS Track Direct

My position About ☰

reset

N0KM-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N0KM-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	Temp*
1778033048	210 Pkts	202 Pkts	26 C
1778029448	219 Pkts	212 Pkts	25 C
1778025848	242 Pkts	235 Pkts	26 C
1778022248	298 Pkts	288 Pkts	26 C
1778018648	258 Pkts	248 Pkts	25 C
1778015048	244 Pkts	233 Pkts	25 C
1778011448	205 Pkts	197 Pkts	25 C
1778007848	257 Pkts	250 Pkts	24 C
1778004248	256 Pkts	246 Pkts	24 C
1778000648	154 Pkts	149 Pkts	24 C
1777997048	175 Pkts	169 Pkts	22 C
1777993448	259 Pkts	253 Pkts	22 C
1777989848	259 Pkts	256 Pkts	22 C
1777986248	271 Pkts	258 Pkts	23 C
1777982648	288 Pkts	277 Pkts	23 C
1777979048	266 Pkts	251 Pkts	24 C
1777975448	291 Pkts	277 Pkts	24 C
1777971848	166 Pkts	153 Pkts	24 C
1777968248	152 Pkts	143 Pkts	25 C
1777964648	155 Pkts	146 Pkts	25 C
1777961048	240 Pkts	226 Pkts	25 C
1777957448	225 Pkts	212 Pkts	25 C
1777953848	166 Pkts	157 Pkts	25 C
1777950248	234 Pkts	221 Pkts	25 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)