APRS Track Direct

My position About ☰

reset

E25XKG-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E25XKG-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Voltage*	Current*	Battery*	CPU*
1790664754	8.9 V	0.7 A	100 %	44 C
1790663854	8.9 V	0.9 A	100 %	43 C
1790662954	8.9 V	0.7 A	100 %	44 C
1790662050	8.9 V	0.8 A	100 %	44 C
1790661150	8.9 V	0.8 A	100 %	42 C
1790660249	8.9 V	0.7 A	100 %	41 C
1790658448	8.9 V	0.8 A	100 %	45 C
1790657548	8.9 V	0.8 A	100 %	44 C
1790656648	8.9 V	0.8 A	100 %	42 C
1790655748	8.9 V	0.9 A	100 %	41 C
1790654856	8.9 V	0.7 A	100 %	44 C
1790653948	8.7 V	0.8 A	100 %	47 C
1790653044	8.9 V	0.8 A	100 %	44 C
1790652144	8.9 V	0.8 A	100 %	41 C
1790651244	8.9 V	0.8 A	100 %	42 C
1790650344	8.9 V	0.7 A	100 %	45 C
1790649444	8.9 V	0.7 A	100 %	40 C
1790648544	8.9 V	0.9 A	100 %	41 C
1790647644	0 V	0 A	0 %	0 C
1790646744	8.9 V	0.7 A	100 %	41 C
1790645844	8.9 V	0.8 A	100 %	40 C
1790644944	8.9 V	0.8 A	100 %	39 C
1790644040	8.9 V	0.7 A	100 %	39 C
1790643140	8.9 V	0.7 A	100 %	39 C
1790642240	8.9 V	0.8 A	100 %	42 C

*Used Equation Coefficients:

Voltage: 0, 0.1, 0

Current: 0, 0.1, 0

Battery: 0, 1, 0

CPU: 0, 1, 0

RSSI: 0, -1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)